parking brake complete

 Below is the worms eye view of the layout for the parking brake cable change I am making.  Left is the focus setup.  Right is the mustang setup.  The main difference is where the cable sheath goes (shown in green).  On the focus it starts from a bracket near the parking brake lever, and it ends at some point near the drum housing.

worms eye view.  Blue is the cable.  Green is the cable sheath.  Red is the cable bit attached to the handbrake.  Left diagram: Focus cable layout. Right diagram: mustang cable layout.

There were 3 problems with the focus cable:

1) The spring on the cable that retracts the parking brake shoe was too short.

2) The clip that holds the cable into the drum housing was flimsy brittle plastic, and the hole was slightly bigger on the drum which put more stress on this plastic.

3) Since the sheath ends before the drum, I would have had to weld up some large bracket to the control arm to receive it

The image on the right shows the mustang cable.  Here the cable goes all the way into the drum housing, so it instantly solves 1,2, and 3.  However, some fab was needed to put the mustang pulleys, and a new sheath termination bracket.

First I had to cut off the old focus parking brake bracket.  This is exactly what the plasma cutter is for:

When I started laying this out, I found that one mustang cable was frozen into the housing, and I couldn't get it to free up so I had to get another from summit before I could continue.  Below is the final routing tacked in. 

Here is the rest of the cable routing to the brake drum housing.  I zip tied the housing to the control arm at least for now to make sure it stays off the tire.

rear brakes

The rear brake lines from my old focus were so rotten that they came apart in my hand.  I bent up some new ones.  My bend tool makes the same diameter that ford uses.  I figured out that if I put in the old line I can mark where the bend begins, then transfer the mark.  

Drivers side brake line and hose:

 Passenger side brake and hose:

I am happy with how that all turned out.  I think it looks more or less factory.

I thought about transferring the spring on the parking brake cable to the focus cables.  But it just seemed like the wrong move.  I was worried that the focus cable wouldn't stay clipped into the drum (it is slightly smaller diameter than the mustang cable.  I was going to have to weld some large weird brackets to the control arms to hold the cable sheath ends, and that would still point the cables at a weird angle.

I layed out the mustang cable and figured out that it is the right length.  So I signed up for some fabricating.  More on that soon.

rear brake hoses and preliminary ebrake

I got an extra set of Focus front brake hoses and used them to finish the rear brake hose connections:

After I welded on the tabs I sprayed them with galvanizing compound.

I want to have a functioning e brake whether inspection requires it or not.  I saved the ebrake cable from the mustang and some pulleys that went with it.  I was really hoping that the focus ebrake cable would work since it is unlikely that I would be able to lay out the mustang cable without significant fabrication and/or luck.

It does look like it the focus brake will work:

Although the Focus end is smaller, it does fit into the ebrake arm in the mustang drum.  The spring is shorter which may cause trouble since the spring is what retracts the brake shoes when you release the brake. I may try to put the mustang spring on this cable, or make a collar or something.  I also need to make a mount to hold the end of the cable sheath.

rear brakes layout

Solid axle cars I have seen use hard lines on the axle with a single hose attaching in the middle.  My axle was set up this way, but the hard lines in the car had a hose at each wheel.  I decided to go with a hose directly to each wheel.  In retrospect it may have been simpler to tee the hard lines in the car together then connected them to the axle at the single point.

Ford has a clever way of doing brake hoses where the hose indexed into its mount with a small tab so it won't rotate:

I was hoping to preserve both this feature and preserve the mounting point for the hose to avoid the extra work I had to do for the front brakes.  I need brake hoses long enough that when I jack up the car I don't hang the axle from the hoses, but not so long that they have enough free movement to touch the tire.
Dorman's website allows me to search hoses by many different criteria.  I don't think three are any hoses with the Ford end that are female - female and long enough to reach.  The front of the car uses a long enough hose that is female - male.  To see if I could make the front hose work I tapped a piece of 11 gage sheet as a braket and there is enough room to thread the hose into it, then thread on a union. It looks about perfect:

The piece in the image and shown below is a bit of hard line I made to connect to the drum brake.  The left end is double flare and connects to the drum brake.  They right end is bubble flare and mates with the hose/union.

driveshaft weld up

It is nice if I think I lathed the end straight, and also nice that I think I cut the shaft tube straight, but I decided driveshaft runout is probably the only thing that counts, so I decided to check it before I tacked it up, and I am glad I did.  There was about.080 TIM.  I looked online and it seems like people think somewhere from .005 to .020 is ok.  People report stuff like .060 being good to 80 mph, sometimes. The transmission end of the shaft measured at .020 so I made that my target.

I marked what was high and low, pulled the shaft out and tried to beat the cap straighter.  Put it back in, and checked it.  After repeating this process 3 or 4 times I was below .020 so I tacked it:

 I made this rig so I could in theory roll the tube while I welded.

It was easy enough to start and stop on the tacks so I didn't need to roll it.  I dipped the tungsten 0 times which was nice.  I could have slid along at like 85 amps and made this beautiful, but the bevel was pretty tight, so I had to really watch to make sure the puddle was wetting all the way to the bottom before jamming rod in.  Consequently I had to bake this a little bit especially with the heavy casting on the other side.  I went at like 110 amps and even that was probably a bit low as I was floored and waiting most of the time.  But it looks pretty good I think:

drive shaft shortening

I installed the slip yoke on the end that already has the right size u joint.

Next I have to liberate the end of the shaft so that I can weld it on later.

by the way, the tubing is .095 wall which was heavier than I expected.  Next I need to separate the steel tube from the casting.
I assume that the shoulder under the trunion is parallel to the u joint axis so I lined the part up based on that:

Then I machined through the weld.  You can see the rust peaking through right as I started to get through the tube and expose the casting:

Ready to weld with a beveled edge:

My u joint came from Amazon to convert from 1 3/16 to 1 1/16.  

Once I had all that together, I would see the distance from the beveled cut to the very end and see where to cut the tube.  I scored it with the cutting disk in the die grinder then finished the cut with the 4 1/2:

Then I heated the end of the tube up with a map gas torch and beat the u joint in.  I used a piece of angle to line up the Ujoints at each end.  I wasn't sure how close the had to be.  A co-worker told me .125° or there would be big trouble.  The internet doesn't seem to agree.  Seems like 5° is common, which I am more inclined to believe (maybe because I have to!)

Here is the end stuck in the transmission.  Pretty much right where it used to be on the yoke:

Here is the end into the pinion.  Looks good.  Not a lot of clearance on the e brake cable

Just need to weld it up

drive shaft planning

Finished painting and welding in the drivers side suspension mounts and control arms.  Since I can't tighten the through bolts super tight (would crush the frame rails) I tacked the nuts and bolt heads down with a spot weld to help hold everything still (locktight is for pansies!).  These bolts are permanent, but if I ever want them out, I put the tack in an easy to cut spot.

I decided to tackle the driveshaft next.  I put the mustang drive shaft up under there and wouldn't you know I need a longer driveshaft, not shorter.  After contemplating combing a junkyard for a manual shift pickup with an 8 foot bed, I decided to just have one made.  I asked my buddy Kenny where he had his made, and he had one laying around and several different size u-joints he said I could have.

Rusty one is from the mustang.  Black one is from Kenny's truck before he went to a two piece driveshaft to fix some vibration issues:

So yes this thing vibrates above about 80 mph.  Shortening it by 20% should cure that, so if I have vibration issues, I will get it balanced and I expect that will be the end of that.  Also, It is fun to think of my car as powerful, but it is nothing compared to kenny's truck so it should be fine.  

The U joint on one end was the right size.  The one on the other end and the two new ones that he gave me are all not the right size.  Drive shaft pivot was 1 3/16 dia, and the bit attaching to the pinion was 1 1/16 dia.  Found a spicer u joint that hits both of those (5-648x) for $30 on Amazon.  So I grabbed some brake hoses to hook up the rear brakes.

Went ahead and removed the u joint from the end of the shaft.  It is nice to have a press for this.  So much more civilized than trying to beat it out of there.